You'll Never Guess This Replace Window Pane's Tricks > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace window pane Window Panes

A cracked window pane can be a nuisance. This can be an opportunity to upgrade your windows to energy efficient or insulated ones, and reap benefits such as improved comfort, increased resale values and reduced utility bills.

You can do it yourself for a less than what it would cost to hire an expert. It requires the right tools and an hour or two of your time.

Glass

Replace your old single-paned windows with tempered insulated glass to increase energy efficiency, reduce noise, and preserve the historic integrity of your home's older. The majority of homeowners with basic hand tools can repair windows with ease. You will also need an additional window pane, glazier's tips pliers, and latex glaze putty. If you need to, you can use a heatgun to warm the old putty. Before beginning, wear gloves and safety goggles as working with broken glass could cause injuries.

Take out any broken glass pieces that remain. It is recommended to use pliers however, a flathead may be useful as well. Then, use a wood chisel, or putty knife, to take the remainder of the old putty around the frame and sash. Be careful and slow making sure not to damage the old window sash. This should be done on a ladder, not on the ground. Also, ensure that someone lower to keep it in place.

Make sure the window frame is ready to accommodate the new pane after you have removed the old glue. To allow for seasonal expansion or contraction, subtract 1/8 inch each from the measurements of width and height. Take these measurements to the nearest hardware store or home center, and find a piece glass cut to size. You can also cut the glass by yourself if you have the right tools.

After putting the new pane in place, run a small bead of caulking around the edge to ensure it is weatherproof. Install a glazier’s point on both sides of the frame. This will ensure the pane. The points shouldn't be tight enough to create friction between the frame and Replace Window Pane sash, but they should also not be loose.

Before applying the putty to the surface, knead thoroughly until it becomes soft and free of lumps. Then make it into pencil-sized strips. Place the first strip in the corner of the frame, working from one corner to the other so that it is smooth and even.

Glazier's Points

The glazier's facets are tiny triangular pieces of steel that allow glass to be secured into the frame of a window without scratching or damaging the delicate surface. It's easy to understand how to use this secret tool and you can save money on the expense of an expert installation.

After getting rid of the old putty glazier points and any residue clean the frame thoroughly using a utility knife. If needed you can lightly sand the wood along rabbet grooves to smooth out rough spots. If you do sand the wood, be sure to protect it by using painter's tape to prevent accidental damage.

Measure the empty frame's dimensions and note down precise measurements. Take these dimensions to an hardware store or home center and have the new pane cut slightly smaller than the frame's opening. This will ensure a snug fit and leave room for expansion and contraction.

Place the new window in the frame and push it into place firmly with your hand. Then, use the tip of your chisel, or the back end of the putty knife to pierce the glazier's points as illustrated in Figure 11. The glazier's points should sit in line with the top edge of your pane and the shoulders raised should be just below that lip.

Apply a thin layer of glazing compound over the edges of the new glass and into the rabbet grooves, to seal and protect them. Allow it to dry and cure completely.

After the glazing compound dries and the glazing compound is dry, you can install the new window sash. First, you need to coat the wood with an even layer of linseed. This will prevent the newly-created putty from drying out and cracking due to the moisture it absorbs. Apply this coat with a brush or the edge of your putty knife, and then employ the chisel or back end of the putty knife to gently hammer in the new sash and glazier's points into the grooves of the rabbet. Repeat this process in intervals of 10 inches all around the frame.

Putty

A baseball thrown at you, an errant rock or a fallen branch can cause a window pane to crack or break. The majority of windows can be replaced by simply putting in a fresh piece. The glass is held in the position with a tiny metal clip, called a glazier's point and putty. This compound is also called glazing compound. Before you install a new pane, first remove the old one and clean the area with an abrasive and an abrasive scraper that is a pull type or the wood chisel. Wear protective glasses and gloves while you do this work. If the window glass replacement is attached to the frame, you'll need make use of a heat gun to soften the adhesive before prying it free.

If you're planning to install the original sash in the future, take care to remove any pieces of molding that are used to secure the old pane. Then sand the sash to ensure it's level and ready for a new caulk. Once the sash is installed, apply a new caulk made of silicone around the glass to ensure that it doesn't swell or fade in time.

Take out the glazing points in the rabbets. These are the grooves in the sash where the glass is located. If they're difficult to chisel, use a hand tool like a heat gun over them for a few minutes to soften them. If you're using a heating gun, be cautious not to cause damage to the railings of the sash or the sash itself by using the tool too close.

Once the old glazing points and putty are removed, make a bed for the new pane. Roll a piece of glazing compound between your hands, and form it to be around 1/2-inch thick. Then, press it into the rabbets, where the glass will sit. The glass must rest against the putty on both sides. If you need to gently tap your glass into the rabbet with your thumb.

If the new pane is damaged, you can use a silicone caulk or glass glue that is based on solvents to seal the crack prior to pressing it into the sash. If not, you'll have to apply putty on the crack to form an airtight seal and keep water out. Once the putty is dry clean the oily film off the glass and let it dry completely before painting. If you paint before the putty is fully dry, it won't form a strong seal and may discolor or leak over time.

Paint

If you've experienced a broken window pane, you might be worried about the expense of replacing it. But the truth is that replacing one glass pane does not have to break the bank If you can do it yourself. In fact windows with double glazed window replacement panes can be replaced at only a fraction of the cost of an expert.

First, if you are working on a large window, Replace Window Pane make sure that it is securely fixed to the frame. With the right tools and techniques, you can make this task relatively easy and quick.

When you are ready to begin taking down the old window pane. Remove the metal glazing points that are attached to it. These are small metal triangles that act as "nails" that hold the window in place. They are placed under a bead or glazing glue that hardens to a solid wedge that holds the frame securely in place and hides the sharp edges.

After you have removed the old pane taken away Clean up the frame and wood. Scrape off any old paint and sand down the rabbet grooves that the glazing points were. These should be sanded to the point of being bare, to allow you to paint them the same color as the rest of the frame. After sanding the wood you can apply a layer flax oil. This will help prolong the life of the frame.

Then, take measurements of the dimensions of the window opening. You will need to take vertical and horizontal measurements of the entire opening, and also the thickness of the old pane. To get the exact size of the new pane, subtract 1/8 inch from both measurements. This will allow for seasonal changes in the glass. You can take these measurements to a hardware or home improvement shop and get the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.